Autosurf -Automatic Wakesurf System Controller
The Autosurf is a simple, compact and GPS wakesurf system controller. By simply clicking the Auto button and picking a side, your surf system will now automatically deploy and retract at a settable speed, just like all modern surf boats! Surf settings can be saved at anytime as well. Switching sides is as easy as clicking SURF RIGHT or SURF LEFT. Wiring is extremely easy, just 7 inputs, 12v fused positive, keyed ACC, negative and positive and negative for each actuator. It can control both gate or tabs systems as long as they are 12v actuators. It is marine rated and virtually waterproof.
Make your surf system automatic!
Theory of operation
The AutoSurf is operated by turning the system on (middle AUTO button). Then clicking the button for what side you will be surfing, SURF LEFT or SURF RIGHT. As the boat gets up to surf speeds 10-12mph the surf tab or gate will deploy (past 5mph, this speed is settable) on the side you have set. Then the +Wave or –Wave (retracts or extends actuator) will allow you to fine tune wave size on each side. A desired surf wave setting can be saved at any time by holding the surf left and surf right (whichever side you are surfing) for 4 seconds. If the surfer falls or is done with the session, the boat tabs will automatically retract below 5mph. At any time the surf side can be switched by simply clicking on SURF LEFT or SURF RIGHT button. The system will then begin to retract and deploy the tabs or gates to the pre saved value. When the key is in the off position tabs/ gates automatically retract. With the key on, the auto system will not fully turn on till the AUTO button is pressed. A small red led will light up once this is done.
The tab or gate that deploys is always the opposite side that you are surfing. So surfing the Left or Port side means the Right or Starboard tab/ gate moves out. Surfing Right means the Port or Left / gate moves out.
The Autosurf is a simple, compact and GPS wakesurf system controller. By simply clicking the Auto button and picking a side, your surf system will now automatically deploy and retract at a settable speed, just like all modern surf boats! Surf settings can be saved at anytime as well. Switching sides is as easy as clicking SURF RIGHT or SURF LEFT. Wiring is extremely easy, just 7 inputs, 12v fused positive, keyed ACC, negative and positive and negative for each actuator. It can control both gate or tabs systems as long as they are 12v actuators. It is marine rated and virtually waterproof.
Make your surf system automatic!
Theory of operation
The AutoSurf is operated by turning the system on (middle AUTO button). Then clicking the button for what side you will be surfing, SURF LEFT or SURF RIGHT. As the boat gets up to surf speeds 10-12mph the surf tab or gate will deploy (past 5mph, this speed is settable) on the side you have set. Then the +Wave or –Wave (retracts or extends actuator) will allow you to fine tune wave size on each side. A desired surf wave setting can be saved at any time by holding the surf left and surf right (whichever side you are surfing) for 4 seconds. If the surfer falls or is done with the session, the boat tabs will automatically retract below 5mph. At any time the surf side can be switched by simply clicking on SURF LEFT or SURF RIGHT button. The system will then begin to retract and deploy the tabs or gates to the pre saved value. When the key is in the off position tabs/ gates automatically retract. With the key on, the auto system will not fully turn on till the AUTO button is pressed. A small red led will light up once this is done.
The tab or gate that deploys is always the opposite side that you are surfing. So surfing the Left or Port side means the Right or Starboard tab/ gate moves out. Surfing Right means the Port or Left / gate moves out.
The Autosurf is a simple, compact and GPS wakesurf system controller. By simply clicking the Auto button and picking a side, your surf system will now automatically deploy and retract at a settable speed, just like all modern surf boats! Surf settings can be saved at anytime as well. Switching sides is as easy as clicking SURF RIGHT or SURF LEFT. Wiring is extremely easy, just 7 inputs, 12v fused positive, keyed ACC, negative and positive and negative for each actuator. It can control both gate or tabs systems as long as they are 12v actuators. It is marine rated and virtually waterproof.
Make your surf system automatic!
Theory of operation
The AutoSurf is operated by turning the system on (middle AUTO button). Then clicking the button for what side you will be surfing, SURF LEFT or SURF RIGHT. As the boat gets up to surf speeds 10-12mph the surf tab or gate will deploy (past 5mph, this speed is settable) on the side you have set. Then the +Wave or –Wave (retracts or extends actuator) will allow you to fine tune wave size on each side. A desired surf wave setting can be saved at any time by holding the surf left and surf right (whichever side you are surfing) for 4 seconds. If the surfer falls or is done with the session, the boat tabs will automatically retract below 5mph. At any time the surf side can be switched by simply clicking on SURF LEFT or SURF RIGHT button. The system will then begin to retract and deploy the tabs or gates to the pre saved value. When the key is in the off position tabs/ gates automatically retract. With the key on, the auto system will not fully turn on till the AUTO button is pressed. A small red led will light up once this is done.
The tab or gate that deploys is always the opposite side that you are surfing. So surfing the Left or Port side means the Right or Starboard tab/ gate moves out. Surfing Right means the Port or Left / gate moves out.